logo
86-574-88328001
TU

0.5mm 304 Spring Wire - Resistivity and Spot Welding

0.5mm 304 Spring Wire - Resistivity and Spot Welding
Temel Özellikler
Menşe Yeri: Çin
Marka Adı: TOPONE
Sertifikasyon: ISO/SGS/RosH
Model Numarası: 304
Ticari Gayrimenkuller
Minimum Sipariş Miktarı: 1000kg
Fiyat: Pazarlık edilebilir
Ödeme Koşulları: T/T,L/C
Tedarik Yeteneği: Ayda 1000 ton
Etiketler:

Paslanmaz Çelik Tel

ss yay teli

ss Tel Bobin
Ürün Özetleri
Tekrarlanabilir dirençli nokta kaynağı için yaklaşık 72 mikro-ohm cm dirençli, sarma için sabun kaplı 0,5 mm 304 yay teli. Talep üzerine çıplak uçlar, 3,1 MTC.
Ürün Özel Nitelikleri
Vurgulamak

0.5mm 304 spring wire

,

304 stainless steel spring wire

,

spot welding spring wire

Sertifika:
ISO,SGS,Rosh
Başvuru:
Yaylar/vida/tel formu/balıkçılık
Çap:
0,15-12 mm
Malzeme:
304
Yüzey:
Parlak/sabun kaplı
Ürün adı:
0.65mm 304Sabun kaplı Paslanmaz Çelik Yay Teli
Tip:
Sert/yumuşak
Ambalaj:
Makara, bobin
Ürün Açıklaması
Ayrıntılı özellikler ve özellikler
0.5mm 304 Spring Wire - Resistivity and Spot Welding Product Introduction TOPONE supplies 0.5 mm 304 stainless steel spring wire with a soap-coated surface for high-speed spring coiling. Many of the springs and wire forms made from this size are later joined by resistance spot welding - to a terminal, a plate or a second wire. The electrical resistivity of 304 is what makes that possible, and understanding it helps set the welding parameters. Coil weight, tensile class and
İlgili Ürünler

302 Yay tel - Çizim Materyal ve Yüzey

302 Spring Wire - Drawing Die Material and Surface Two suppliers can draw the same rod down to 1.4 mm in 302 and deliver wire that looks the same on a certificate but differs on the surface. The difference is usually the die: which material it was made from, how long it has run, and whether the ...

302 Yay Teli - Ovalite ve Çap Tutarlılığı

302 Spring Wire - Ovality and Diameter Consistency A diameter tolerance says how far the wire may sit from nominal. It does not say whether the cross section is round. A wire measuring 0.80 mm on one axis and 0.76 mm on the other can pass a tolerance of plus or minus 0.02 mm on both readings and ...

Paslanmaz Tel 0,15-12mm, Çap Tolerans Kontrolü

Stainless Steel Wire Diameter Tolerance and How It Is Measured Diameter is the one number on a wire purchase order that both sides assume is understood, and it is also the one that causes most disputes. A tolerance band quoted without a measuring method can be met by one instrument and missed by ...

Korozyona Dirençli Paslanmaz Tel 0,15-12mm, Tavlı

Corrosion Resistant Stainless Steel Wire, Annealed 0.15-12 mm Corrosion resistance is usually discussed as a grade property, but on a finished part it is often a processing property. Cold drawing leaves residual tensile stress in the wire, and that stress is where chloride pitting and stress ...