logo
86-574-88328001
SP

Stainless Spring Wire 302 - Marked Splices, Stable Feed

Stainless Spring Wire 302 - Marked Splices, Stable Feed
Propiedades básicas
Lugar de origen: China
Nombre de la marca: TOPONE
Proceso de dar un título: ISO/SGS/RosH
Número de modelo: 302
Propiedades comerciales
Cantidad mínima de pedido: 1000 kilos
Precio: Negociable
Condiciones de pago: LC, T/T
Capacidad de suministro: > 1000 toneladas al mes
Etiquetas:

Alambre de acero inoxidable

alambre de resorte ss

ss bobina de alambre
Resumen del producto
302 Stainless Spring Wire with Marked Splices for Planned Coil Changes Product Introduction Long spring wire coils contain at least one splice, because drawing and annealing equipment works in finite lengths. What matters on a coiler is not that a splice exists, but whether the operator knows where ...
Atributos personalizados del producto
Resaltar

302 stainless spring wire

,

marked splice spring wire

,

stable feed stainless wire

Estándar:
Los datos de los Estados miembros deben estar disponibles en el sitio web de la Agencia.
Tratamiento superficial:
Brillante / revestido de jabón
Calificación:
302
Solicitud:
Las condiciones de ensayo de las pruebas de ensayo deberán ser las siguientes:
Embalaje:
Bobina/paleta
Diámetro:
0,8 mm
Tipo:
Duro
Resistencia a la tracción:
Se aplicarán las siguientes medidas:
Certificación:
ISO,SGS,RosH
Descripción del Producto
Especificaciones y Características Detalladas
302 Stainless Spring Wire with Marked Splices for Planned Coil Changes Product Introduction Long spring wire coils contain at least one splice, because drawing and annealing equipment works in finite lengths. What matters on a coiler is not that a splice exists, but whether the operator knows where it is before the wire reaches the feed rolls. Every splice in this wire is a butt weld, annealed at the joint, dressed flush, and marked with a tag and paint mark placed ahead of
Productos relacionados

302 Stainless Wire - Shot Peening and Residual Stress

302 Stainless Wire - Shot Peening and Residual Stress A spring almost always fails by fatigue, and fatigue almost always starts at the surface. That single fact explains why shot peening, a process that does not change the material or the dimensions at all, can multiply the life of a part. Peening ...

Alambre inoxidable de 0,15 a 12 mm, control de trefilado fino

Fine Stainless Steel Wire: Where Breakage Comes From in Drawing Below about 0.5 mm the wire stops behaving like wire and starts behaving like a filament. Surface finish, tension and heat build-up dominate, and a defect that would pass unnoticed on 2 mm becomes a break at the die or a snap at the ...

Alambre inoxidable de 0,15 a 12 mm, vida útil por fatiga por flexión cíclica

Cyclic Bending Fatigue in Stainless Steel Wire: Where Failures Start A wire that survives one bend and a wire that survives a million cycles are two different specifications, even when both are the same grade and the same diameter. Fatigue is a surface and stress-amplitude problem, and the grade ...

Soft Annealed Stainless Wire 0.15-12mm for Cold Forming

Soft Annealed Stainless Steel Wire for Cold Forming, 0.15-12 mm Cold forming shops care about two numbers on a soft annealed wire: how much force the part needs at the bend, and how much that force moves from coil to coil. A wire that is soft on Monday and half work-hardened on Friday changes press ...