logo
86-574-88328001
IT

Corrosion Resistant Stainless Wire 0.15-12mm, Annealed

Corrosion Resistant Stainless Wire 0.15-12mm, Annealed
Proprietà di base
Luogo d'origine: Cina
Marchio: TOPONE
Certificazione: ISO9001:2015
Numero di modello: 201/302/304/316/316L
Proprietà commerciali
Quantità minima di ordine: 1000 kg
Prezzo: Negoziabile
Termini di pagamento: D/P,L/C,T/T
Capacità di fornitura: >10000KGS alla settimana
Tag:

Bobina del cavo di acciaio inossidabile

filo ricotto brillante

ss bobina di filo
Riepilogo Prodotto
Corrosion Resistant Stainless Steel Wire, Annealed 0.15-12 mm Corrosion resistance is usually discussed as a grade property, but on a finished part it is often a processing property. Cold drawing leaves residual tensile stress in the wire, and that stress is where chloride pitting and stress ...
Attributi personalizzati del prodotto
Evidenziare

Annealed Stainless Wire 0.15-12mm

,

Corrosion Resistant Stainless Wire

,

Annealed Stainless Steel Wire

Materiale:
1,4567
Imballaggio:
dalla richiesta del cliente
Standard:
EN DI JIS G. ASTM. BACCANO. GB ecc
Superficie:
Matt o luminoso
Capacità di alimentazione:
>500 tonnellate al mese
Diametro:
0.15-12mm
Descrizione del prodotto
Specifiche e Caratteristiche Dettagliate
Corrosion Resistant Stainless Steel Wire, Annealed 0.15-12 mm Corrosion resistance is usually discussed as a grade property, but on a finished part it is often a processing property. Cold drawing leaves residual tensile stress in the wire, and that stress is where chloride pitting and stress corrosion cracking start. Annealing after drawing is the step that removes it. This wire is annealed and supplied bright or acid-pickled, from 0.15 mm to 12 mm, in 304, 304L and 316L. The
Prodotti correlati

Annealed Stainless Wire 0.15-12mm, Bend Radius Guide

Minimum Bend Radius on Annealed Stainless Wire: A Practical Guide When a drawing specifies a bend, the question behind it is usually whether the wire will crack at that radius. The answer depends on three things: wire diameter, the tensile band of the coil, and where surface defects sit relative to ...

6.5mm 304 Stainless EPQ Wire - Heavy Forming Grade

6.5mm 304 Stainless Steel EPQ Wire for Heavy Wire Forming At 6.5mm, wire forming loads and spring-back are significantly higher than for fine wire, so the wire must combine controlled diameter, annealed ductility and a clean surface. This EPQ (extra press quality) wire is produced in 304 grade, with ...

Brush Steel Wire Spool 0.15-12mm - Consistent Tufting

Brush Steel Wire Spool for Consistent Brush Tufting Brush steel wire is used for industrial brush manufacturing, where tufting quality depends on stable wire diameter, controlled straightness and consistent surface condition. This wire is cold drawn and supplied on BS60, BP60 or DIN wooden spools, ...

Filo di fissaggio in acciaio inossidabile 304Cu per intestazione a freddo | 0,15–12 mm

304Cu Stainless Steel Fastener Wire for Cold Heading | 0.15–12mm Product Introduction TOPONE Wire supplies 304Cu stainless steel fastener wire for cold heading and cold forming applications, including screws, bolts, nails, rivets, pins and other stainless steel fasteners. The wire is available in ...